All I can say is wow!!! Now my headlights are nice and bright. Some people have a different version of fuse card as you can see here but that doesnt show headlight Im have a problem with the headlights in Auto Mode. We are very satisfied with the results and will be purchasing this product for our other car. I removed the switch cleaned it tested it replaced it. I just turned the tire facing out on the broken side.
I do not think they would be a good fit. I pulled the bezel trim off of the fog light to see if I could reach in from there but there wasnt enough room for my hand. Kelly Hudgens First, they were cut perfectly but they are thick - nothing like those screen protectors for phones, iPads, etc. Cold I have both the comfort access and the headlight washers. I bought this ballast, installed it which includes removing the front bumper cover , and the bulb fired right up.
When I pulled in the drive I discovered neither headlight halogens will come on. The adjustment is probably fairly simple but since its an 09 car id bring it in and ask how that could have happened. Did anybody notice a similar problem Is that normal I was passing by the dealer this morning and decided to stop and see what they say. Then you can reach in, pull the wire connector off the bulb, and unclip a metal retainer over the bulb, and pull the bulb out. The bumper info looks great. Please help Thank you in advance. Thanks for the tip guys.
I was able to remove almost all the air bubbles with my fingers then used the squeegee to remove the soapy solution. You will have vertical adjustment screws for each independent beam separate highs and separate lows, but will be same screw if highs and lows are the same bulb. I dont notice that much of a difference in real world tests. Though they are widely distributed throughout the industry, and their quality rivals that of the German and Japanese lighting giants, they do almost no marketing, instead pouring every dollar into the development and optimization of their Head Light Bulb line. Recently, when I needed something to do, I decided that I would install them and take my chances. Turn the dial about 1 turn at a time and notice which way the headlight moves. What I wound up doing though since I couldnt pull it out since the cover was already off I tried reaching in from the front but I was afraid that with the amount of force I would need to pull it out I might break something.
Installation WeatherTech recommends professional installation, but LampGard comes with easy-to-follow instructions and applies to headlamps, fog lamps, turn indicators and parking lights when applicable to protect them from scratching and pitting. I unscrewed the washer fluid tank and move it out of way. So they have repalced it and its working perfectly. That is exceptional customer support and should build confidence in anyone's purchase. My car had four pieces running lights and headlamps and all were precision-cut to fit like a glove. I did see 2 white dials but not sure if this is what I need to adjust the headlight with or which one to use.
If you have any questions, feel free to call our toll free order line. This is a prime example of excellent customer service. I had to use some tapes to keep the ignitor in place on the retainer. No modification necessary - plug-and-play installation! If you want to do it you must take off the entire headlight and bake it in the oven. Changing both headlight bulbs on your X3 at the same time will allow both bulbs to have the same intensity and prevent the new headlight bulb from appearing brighter than the bulb on the opposite side. Keep in mind this is looking at it on an even level. I then stuck the loose hose up by the fill nozzle and put the fill nozzle and headlight electrical plug back on.
Fits left or right headlight. LampGard is available for many vehicle makes and models. Is there an easy way to disable just the headlight washers perhaps a fuse Thanks. Tested it on the other working headlight as recommended and it blew a bulb no i didn't touch the bulb, and yes I had the working ballast on the other side plugged in No worries though I had new bulbs to replace while I had the bumper off. This really is a non-issue with the only impact being a safety benefit.
Although, very few and seemingly simple, I was immediately concered about being able to curve the protector over and around the headlight. Any suggestions Im posting this as a warning and notice to other X3 owners who work on their own vehicles from time to time. They should not come on when the head lights are off. It all depend on how much snowroad grime you get and if you find yourself having to do like I just said. Can anyone tell me how to release it so I can remove the bulb The bulbs are in the mountings the writing on the label is right side up so the pics are rotated 90 deg clockwise. There was very little clouding of the lens when I finished and 7 hours after I installed them they are almost clear. The LampGard Headlight Protection is the very best product one can imagine.