Tighten the bolts to 115-151 in lbs 13-17 Nm. There is a five-second window that begins from the first transition of the unlock switch. I think it is just under the dash but you may have to remove the glove box. I also include what someone else gave as advice. Can you unplug them and only effect the airbags from working? For additional information, refer to Section 414-01. Once those plugs are removed, work the fuse panel down toward the floor.
The installation is the reverse of the removal. Except when the seven position switch is in interval 1, the speed dependent wipers will compensate for the extra moisture that accumulates on the windshield at higher speeds. Jun 23, 2009 here it is but you must have it configured. You don't know if the one your buying is bad as well. Jan 10, 2012 Hi, Did you also check fuses on fuse panel in the engine compartment? One wiring harness needs to be disconnected from the panel.
The windshield wipers remain parked until the windshield wiper motor module completes a time-out and then repeats the intermittent windshield wiper cycle. It is behind the radio. These are the only operations of a 1995 Gem Module that I'm aware of that are controlled by the Gem Module. The key chime would be a sympom of that. If there is water then you will need to replace the fuse panel and gem module that is mounted to it.
Getting one form the boneyard seems a little risky. Apr 30, 2018 Do you know how to do electrical testing? Jim, am I right in thinking that Deven pulling the fuse would cause the P0603 code? It is mounted on the back of the interior fuse panel. I have a 1995, and it is on top of the radiator frame. You have to lay on your back and look up. The Gem Module Controls: 1. I hope I have helped you with your problem.
Remove the steering column opening cover. Verify measurements at pin location. If not, then there is something the matter with the wiper control or its wiring. If exposed to these charges, damage may result. Low Speed Windshield Wipers Low speed is activated when the multifunction switch supplies a specific ground to the speed inputs of the windshield wiper motor module. The vehicle may need to be driven 16 km 10 mi or more to relearn the strategy.
The brake lights if the blinkers the running lights the head lights int lights all work must be the contact point or switch at the brake padal or a ground issue to the bulbs or the bulbs are incorrect Ford has this issue with the bulbs they look the same but there not check that for the brake lights. Good Luck the ignition module can be in 1 of 2 places for that year and depending on the size of motor. Two Ford Dealers … in my town never heard tell. Now the screws for the fuse box can be removed. What is a Generic Electronic Module? I have the same issue. T … here is a big white sticker with 5 numbers starting with number 1.
If you lift that black plastic piece up, the integrated relay control module is right underneath it. Those two are at the lower edge of the fuse box. Disconnect the battery ground cable. I would remove the 2 large connectors located on the bottom back of the interior fuse panel they are held in with 2 10mm bolts and see if there is water present. Make sure it's your type. The assembly is now free of the vehicle. I had one that fixed itself by doing that.
Slide the blade of the screw driver under the edge of the switch carefully and twist slowly until you can see the switch coming up. I believe ford calls it a gem module. Manual shift or Four-Wheel Drive Systems - Electronic Shift I'm assuming you have electronic shift because you refer to relay clicking behind the instrument panel. A baqttery junction box under the hood on the drivers side and one inside on drivers side. I have had the same problem the lights work they done work correctly and its hard to tell. Why to these things beep? Remove the instrument panel steering column cover.
This can be caused by obstruction of the windshield wipers or a binding linkage. Jim, am I right in thinking that Deven pulling the fuse would cause the P0603 code? Did you check the wiper relay's in the under hood fuse box? Since he has none of these does anyone have an idea of what would cause his problems without throwing a code? Where is the computer on the expedition located at? All interior courtesy lamps are turned off when any of the following occurs: l All the doors are closed and the illuminated entry feature is not active. Since he has none of these does anyone have an idea of what would cause his problems without throwing a code? It makes it a little easier to remove if you move the shifter all the way down to drive 1. For additional information, refer to Section 501-20B. Remove the plastic, and you'll see two modules.
No they don't have distributor caps. Remove the bulkhead electrical connectors f … rom the B instrument panel fuse junction panel. Most auto computers are pretty monolithic - one piece. Also ,did you check fuse's? Install the three wiper motor-to-wiper module assembly retaining bolts. You may need to re position the switch as there is a bit of play in the hole the switch fits into to. First remove the two large plugs with the large wiring harnesses from the back of the fuse panel. .