You have to disconect the battery first. They also take advantage of your vehicle's existing connections to simplify installation as much as possible. Whether they're damaged in an accident or simply burn out over time, your Pontiac Grand Am's headlights may eventually need to be replaced. Channel Lock to release hose clamps. Or just use a flat head screwdriver to lift the center part of the fastener. The high beams lights stay on as long as you hold the lever, but the low beam headlights do not work.
Remove the wheel, from the car. When unscrewing the plastic collar off of… In order to replace the headlight bulb on a 99-01 ga gt the ram air cover needs to be removed. Pull the centers out of the 8 plastic clips to remove them. I will get pictures some day. Easiest way to lift off the fasteners is with an interior trim tool.
Handle the bulb only by its base. There are 4 bolts that release the whole headlight and level and etc. Good luck… This is for the passenger side headlight assembly. Then consult your owner's manual for the headlight bulb lamp replacement procedure. Check the rotor, for grooving,glazing, and warpage, also thickness. It was a real help for me when I did it. Now the fun part you have to get it out of the engine compartment.
Next, you will have to remove the top mount located on the side of the engine nearest the belt. You can recognize it by noting that Avery other pulley in the engine bay has grooves that the servpentine belt rests in but the tensioner pulley is smooth and the belt rides on the smooth side of the belt. Your Pontiac Grand Am gets you where you need to be in style. Push inward and pull up on the clips. Then remove the 4-5 small bolts that are holding on the water pump housing.
The driver's side is has a plastic cover that must be removed first, so the setup underneath may or may not be different. You may want to consider replacing… ok i have a 2001 so it may be the same. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. That will make sure there is a good connection between the battery and the electrical system. Try a chiltons manual or www.
The voltage circuit to headlamp switch is orange, hot all the time. You can pull up on these with your fingers, but if too tight it may take a pair of pliers. Let the oil drain and look into the hole… The oil filter is under the hood to the right of then engine in the front. It is very easy by turning two L-shaped knobs just behind the assembly. Now you can roll the headlight assembly out of the car. Electrical problem 1995 Pontiac Grand Am 6 cyl 97,000 miles I am in the process of purchasing a 1995 Grand Am for my son.
Then consult your owner's manual for the headlight bulb replacement procedure. Next, remove the upper radiator hose from where it connects to the engine by loosening the hose clamp. Important: Note the location and position of the headlamp adjuster retainers and the locator tab. Remove the three 10mm hex bolts from the top of the headlight assembly holding it to the vehicle. Disconnect the electrical connector from the headlamp assembly. To help avoid personal injury: Turn off the lamp switch and allow the bulb to cool before changing the bulb.
Remove the hose from the fitting. Lift up the headlamp assembly retainers to release. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. First, remove the air duct from the air filter housing and the air intake connection to the engine. Fortunately, once you've purchased the right replacement bulb for your model year, performing the repair is relatively easy. My dad who is by no means a mechanic checked out the car and everything looks okay except the low beam headlights do not work.
Follow the upper radiator hose to the engine to locate the thermostat. The parking lights work fine. Good luck : Dave The process is the similar for all grand prix trim levels '97 to 03 Caution Halogen bulbs contain gas under pressure. See sources and related links below for replacement bulb information. It has a plastic cap that spins off and if you look at it the container he filter goes in looks like the filter would fit right in.
Then just unplug… Drain fluid. Handling a bulb improperly could cause it to shatter into flying glass fragments. Handle… This is a simple one. Yes, you have to change the entire hub assy. With the hood open remove the 2 two headlamp assembly bolts from the upper fascia support. You must remove the whole headlight assembly.